Within two days of receiving my eero device, I’ve got serial console root login! I’ll detail how I did it in future posts.
U-Boot 2012.07 [standard IPQ806X.LN,r37758] (Apr 08 2016 - 19:01:11) 1.1.0 smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Detected N25Q064A with page size 64 KiB, total 8 MiB ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x800000 8 MiB MMC: ipq_mmc: 0 PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS cdp: get part failed for rootfs Net: athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done eth0, eth1 (Re)start USB... USB0: Register 2000240 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found USB1: Register 2000240 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 1 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Invalid boot device ** Hit any key to stop autoboot: 9 0 (eero) # <INTERRUPT> (eero) # <INTERRUPT> (eero) # <INTERRUPT> (eero) # <INTERRUPT> (eero) # printenv baudrate=115200 bootarg_offset=44000000 bootargs=root=/dev/mmcblk0p3 loglevel=7 rdinit=/bin/kinit rw single console=ttyMSM0,115200n8 earlyprintk bootcmd=ext2load mmc 0:1 0x44000000 eero_kernel.itb && bootm; reset bootdelay=9 eth1addr=[redacted] ethact=eth0 ethaddr=[redacted] fdt_high=0xffffffff ipaddr=192.168.2.101 machid=12ce ramdisk_offset=44000000 stderr=serial stdin=serial stdout=serial ver=U-Boot 2012.07 [standard IPQ806X.LN,r37758] (Apr 08 2016 - 19:01:11) 1.1.0 Environment size: 520/65531 bytes (eero) # reset resetting ... Resetting with watch dog! U-Boot 2012.07 [standard IPQ806X.LN,r37758] (Apr 08 2016 - 19:01:11) 1.1.0 smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Detected N25Q064A with page size 64 KiB, total 8 MiB ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x800000 8 MiB MMC: ipq_mmc: 0 PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS cdp: get part failed for rootfs Net: athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done eth0, eth1 (Re)start USB... USB0: Register 2000240 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found USB1: Register 2000240 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 1 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Invalid boot device ** Hit any key to stop autoboot: 9 8 7 6 5 4 3 2 1 0 Loading file "eero_kernel.itb" from mmc device 0:1 (kernel0) 6387320 bytes read ## Booting kernel from FIT Image at 44000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM OpenWrt Linux-3.14 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e0 Data Size: 6358649 Bytes = 6.1 MiB Architecture: ARM OS: Linux Load Address: 0x42208000 Entry Point: 0x42208000 Hash algo: crc32 Hash value: e7ae46ce Hash algo: sha1 Hash value: ea1e3c6c76154f6e8212647e82aefb2d9d54de7f Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 44000000 Using 'config@1' configuration Trying 'fdt@1' FDT blob subimage Description: ARM OpenWrt qcom-ipq8062-ap145 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x44610898 Data Size: 27323 Bytes = 26.7 KiB Architecture: ARM Hash algo: crc32 Hash value: 52066729 Hash algo: sha1 Hash value: 70d930c22aafc2a44a1f8955cd1477a07240769f Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x44610898 Uncompressing Kernel Image ... OK Using Device Tree in place at 44610898, end 4461a352 Using machid 0x12ce from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.14.0 (root@build) (gcc version 4.7.3 (Ubuntu/Linaro 4.7.3-12ubuntu1) ) #5 SMP PREEMPT Fri Apr 29 01:05:37 UTC 2016 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Ignoring memory below PHYS_OFFSET: 0x40000000-0x42000000 [ 0.000000] Machine model: Qualcomm IPQ8062/AP145 [ 0.000000] cma: CMA: reserved 8 MiB at 5f800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @9d419000 s8064 r8192 d12416 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: root=/dev/mmcblk0p3 loglevel=7 rdinit=/bin/kinit rw single console=ttyMSM0,115200n8 earlyprintk [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 466852K/491520K available (7346K kernel code, 331K rwdata, 1888K rodata, 1655K init, 814K bss, 24668K reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0x9e800000 - 0xff000000 (1544 MB) [ 0.000000] lowmem : 0x80000000 - 0x9e000000 ( 480 MB) [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB) [ 0.000000] .text : 0x80208000 - 0x80b0cc78 (9236 kB) [ 0.000000] .init : 0x80b0d000 - 0x80caaf80 (1656 kB) [ 0.000000] .data : 0x80cac000 - 0x80cfec38 ( 332 kB) [ 0.000000] .bss : 0x80cfec38 - 0x80dca7dc ( 815 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Offload RCU callbacks from all CPUs [ 0.000000] Offload RCU callbacks from CPUs: 0-1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000012] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 687194767200ns [ 0.000289] Console: colour dummy device 80x30 [ 0.000899] Calibrating delay loop... 818.38 BogoMIPS (lpj=4091904) [ 0.041426] pid_max: default: 32768 minimum: 301 [ 0.041569] Security Framework initialized [ 0.041613] AppArmor: AppArmor disabled by boot time parameter [ 0.041689] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.041704] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.049153] CPU: Testing write buffer coherency: ok [ 0.049435] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.049505] Setting up static identity map for 0x4221a080 - 0x4221a0b4 [ 0.125318] CPU1: Booted secondary processor [ 0.186144] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.186285] Brought up 2 CPUs [ 0.186304] SMP: Total of 2 processors activated (1231.25 BogoMIPS). [ 0.186313] CPU: All CPU(s) started in SVC mode. [ 0.187141] devtmpfs: initialized [ 0.205896] VFP support v0.3: implementor 51 architecture 0 part 4d variant 2 rev 0 [ 0.206496] pinctrl core: initialized pinctrl subsystem [ 0.207341] regulator-dummy: no parameters [ 0.211759] NET: Registered protocol family 16 [ 0.217443] DMA: preallocated 6144 KiB pool for atomic coherent allocations [ 0.218616] cpuidle: using governor ladder [ 0.243224] scm_call failed with error code -4 [ 0.243254] read_version: Error in QFPROM read (-95, 0) [ 0.243272] [ 0.243272] Version Read Failed with error -95 [ 0.246772] ipq8064-pinctrl 800000.pinmux: Invalid config param 000a [ 0.246794] ipq8064-pinctrl 800000.pinmux: pin_config_group_set op failed for group 1 [ 0.246816] ipq8064-pinctrl 800000.pinmux: Error applying setting, reverse things back [ 0.246843] ipq8064-pinctrl 800000.pinmux: failed to select default state [ 0.250894] qcom_rpm 108000.rpm: RPM firmware 1.0.133 [ 0.266888] bio: create slab <bio-0> at 0 [ 0.320625] qcom_pcie 1b500000.pci: link initialized 0 [ 0.320881] qcom_pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.320904] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.320917] pci_bus 0000:00: root bus resource [io 0xfe00000-0xfefffff] [ 0.320932] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.321662] PCI: bus0: Fast back to back transfers disabled [ 0.321683] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.322833] PCI: bus1: Fast back to back transfers disabled [ 0.323007] pci 0000:00:00.0: BAR 14: assigned [mem 0x08000000-0x081fffff] [ 0.323025] pci 0000:00:00.0: BAR 15: assigned [mem 0x08200000-0x082fffff pref] [ 0.323047] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.323106] pci 0000:01:00.0: BAR 6: assigned [mem 0x08200000-0x0820ffff pref] [ 0.323122] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.323149] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.323174] pci 0000:00:00.0: bridge window [mem 0x08200000-0x082fffff pref] [ 0.382669] qcom_pcie 1b700000.pci: link initialized 0 [ 0.382901] qcom_pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.382917] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.382931] pci_bus 0001:00: root bus resource [io 0x31e00000-0x31efffff] [ 0.382945] pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.383610] PCI: bus0: Fast back to back transfers disabled [ 0.383628] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.384765] PCI: bus1: Fast back to back transfers disabled [ 0.384932] pci 0001:00:00.0: BAR 14: assigned [mem 0x2e000000-0x2e1fffff] [ 0.384949] pci 0001:00:00.0: BAR 15: assigned [mem 0x2e200000-0x2e2fffff pref] [ 0.384968] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.385023] pci 0001:01:00.0: BAR 6: assigned [mem 0x2e200000-0x2e20ffff pref] [ 0.385038] pci 0001:00:00.0: PCI bridge to [bus 01] [ 0.385064] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.385085] pci 0001:00:00.0: bridge window [mem 0x2e200000-0x2e2fffff pref] [ 0.385871] SDCC Power: 3300 mV [ 0.386192] SDCC I/O Power: 1800 mV [ 0.386238] SDCC I/O Power: Failed to create debugfs directory [ 0.386474] Core Power: 1150 mV [ 0.387964] vgaarb: loaded [ 0.388606] SCSI subsystem initialized [ 0.389274] usbcore: registered new interface driver usbfs [ 0.389372] usbcore: registered new interface driver hub [ 0.389564] usbcore: registered new device driver usb [ 0.393988] i2c-gpio i2c.12: using pins 57 (SDA) and 58 (SCL) [ 0.394385] msm_bus_fabric_init_driver [ 0.395959] pcie_init: pcie_init: unable to create IPC log context for pcie0-short [ 0.395974] pcie_init: pcie_init: unable to create IPC log context for pcie0-long [ 0.395984] pcie_init: pcie_init: unable to create IPC log context for pcie1-short [ 0.395993] pcie_init: pcie_init: unable to create IPC log context for pcie1-long [ 0.396473] Switched to clocksource dg_timer [ 0.396876] FS-Cache: Loaded [ 0.397156] CacheFiles: Loaded [ 0.413000] NET: Registered protocol family 2 [ 0.413929] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.413969] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.414026] TCP: Hash tables configured (established 4096 bind 4096) [ 0.414068] TCP: reno registered [ 0.414091] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.414113] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.414395] NET: Registered protocol family 1 [ 0.674978] msm_rpm_log_probe: OK [ 0.676940] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.677030] audit: initializing netlink subsys (disabled) [ 0.677138] audit: type=2000 audit(0.660:1): initialized [ 0.686939] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.687210] fuse init (API version 7.22) [ 0.696449] NET: Registered protocol family 38 [ 0.697889] Crypto Speed tests [ 0.697947] OCF: testing ... [ 0.697961] crypto_newsession failed 22 [ 0.698050] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.698064] io scheduler noop registered [ 0.698075] io scheduler deadline registered (default) [ 0.698294] io scheduler cfq registered [ 0.700551] crc32: CRC_LE_BITS = 32, CRC_BE BITS = 32 [ 0.700565] crc32: self tests passed, processed 225944 bytes in 1068160 nsec [ 0.701631] crc32c: CRC_LE_BITS = 32 [ 0.701642] crc32c: self tests passed, processed 225944 bytes in 522880 nsec [ 1.191579] crc32_combine: 8373 self tests passed [ 1.682172] crc32c_combine: 8373 self tests passed [ 1.683588] PCI: enabling device 0000:00:00.0 (0140 -> 0143) [ 1.684091] PCI: enabling device 0001:00:00.0 (0140 -> 0143) [ 1.685051] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 1.685067] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.685184] pcieport 0001:00:00.0: Signaling PME through PCIe PME interrupt [ 1.685200] pci 0001:01:00.0: Signaling PME through PCIe PME interrupt [ 1.688016] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 1.688543] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0 [ 1.689248] tcsr 1a400000.tcsr: setting usb port select = 3 [ 1.782484] msm_serial 16340000.serial: msm_serial: detected port #0 [ 1.782609] msm_serial 16340000.serial: uartclk = 1843200 [ 1.782680] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 184, base_baud = 115200) is a MSM [ 1.783251] msm_serial: console setup on port #0 [ 2.650998] console [ttyMSM0] enabled [ 2.655890] msm_serial: driver initialized [ 2.659553] msm_serial_hs module loaded [ 2.663076] qca_serial_hs_init: error creating logging context [ 2.668204] [ 2.668204] Loaded Module Successfully! [ 2.674855] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 2.679605] m25p80 spi32766.0: n25q064a (8192 Kbytes) [ 2.685302] 7 ofpart partitions found on MTD device spi32766.0 [ 2.690335] Creating 7 MTD partitions on "spi32766.0": [ 2.695989] 0x000000000000-0x000000220000 : "bootstrap" [ 2.706344] ftl_cs: FTL header not found. [ 2.706388] 0x000000220000-0x0000002a0000 : "u-boot" [ 2.713360] ftl_cs: FTL header not found. [ 2.715433] 0x0000002a0000-0x0000002e0000 : "u-boot env" [ 2.721187] ftl_cs: FTL header not found. [ 2.724719] 0x0000002e0000-0x000000320000 : "art" [ 2.730412] ftl_cs: FTL header not found. [ 2.733313] 0x000000320000-0x000000330000 : "identity" [ 2.738291] ftl_cs: FTL header not found. [ 2.742343] 0x000000330000-0x000000340000 : "secret" [ 2.747398] ftl_cs: FTL header not found. [ 2.751455] 0x000000340000-0x000000800000 : "scratch" [ 2.760524] ftl_cs: FTL header not found. [ 2.760743] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 2.775518] libphy: Fixed MDIO Bus: probed [ 2.776206] libphy: GPIO Bitbanged MDIO: probed [ 2.820125] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 4.778272] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu> [ 4.779249] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu> [ 4.784744] edma module_init [ 4.794079] PPP generic driver version 2.4.2 [ 4.797071] PPP MPPE Compression module registered [ 4.800800] NET: Registered protocol family 24 [ 4.805436] PPTP driver version 0.8.5 [ 4.810872] usb30.5 supply gdsc not found, using dummy regulator [ 4.814527] dwc3 11000000.dwc3: no usb2 phy configured [ 4.819742] platform 11000000.dwc3: Driver dwc3 requests probe deferral [ 4.824746] usb30.6 supply gdsc not found, using dummy regulator [ 4.831965] dwc3 10000000.dwc3: no usb2 phy configured [ 4.837448] platform 10000000.dwc3: Driver dwc3 requests probe deferral [ 4.842869] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.848912] ehci-pci: EHCI PCI platform driver [ 4.855546] ehci-platform: EHCI generic platform driver [ 4.861308] 100f8800.phy supply vddcx not found, using dummy regulator [ 4.865112] 100f8800.phy supply v3p3 not found, using dummy regulator [ 4.871797] 100f8800.phy supply v1p8 not found, using dummy regulator [ 4.878282] 100f8800.phy supply vbus not found, using dummy regulator [ 4.884823] 110f8800.phy supply vddcx not found, using dummy regulator [ 4.891140] 110f8800.phy supply v3p3 not found, using dummy regulator [ 4.897540] 110f8800.phy supply v1p8 not found, using dummy regulator [ 4.903975] 110f8800.phy supply vbus not found, using dummy regulator [ 4.911009] 100f8830.phy supply vddcx not found, using dummy regulator [ 4.916898] 100f8830.phy supply v1p8 not found, using dummy regulator [ 4.923288] qcom-dwc3-ssphy 100f8830.phy: cannot get HSIO settings from device node, using default values [ 4.929860] 110f8830.phy supply vddcx not found, using dummy regulator [ 4.939380] 110f8830.phy supply v1p8 not found, using dummy regulator [ 4.945714] qcom-dwc3-ssphy 110f8830.phy: cannot get HSIO settings from device node, using default values [ 4.953760] mousedev: PS/2 mouse device common for all mice [ 4.962757] input: gpio-keys.14 as /devices/soc.3/gpio-keys.14/input/input0 [ 4.968349] i2c /dev entries driver [ 4.977376] tmp102 0-0048: initialized [ 4.978927] tmp102 0-0049: initialized [ 4.982727] tmp102 0-004a: initialized [ 4.993171] GPIO_WDT: failed to register misc device [ 4.993217] Error: Driver 'gpio-wdt' is already registered, aborting... [ 4.998060] SPEED BIN: 0 [ 5.003540] ACPU PVS: 2 [ 5.006330] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19) [ 5.008681] deviceless supply vcore_regulator not found, using dummy regulator [ 5.015686] platform cpufreq-krait.0: Driver cpufreq-krait requests probe deferral [ 5.023580] ipq8064-pinctrl 800000.pinmux: invalid group "gpio12" for function "sdc1" [ 5.031922] mmc0: SDCC Version: 0x06000018 [ 5.038222] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 136,0 (pio) [ 5.043409] mmci-pl18x 12400000.sdcc: DMA channels RX dma0chan1, TX dma0chan2 [ 5.097128] sdhci: Secure Digital Host Controller Interface driver [ 5.097162] sdhci: Copyright(c) Pierre Ossman [ 5.102449] Synopsys Designware Multimedia Card Interface Driver [ 5.107280] usbcore: registered new interface driver ushc [ 5.112709] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.121849] deviceless supply vcore_regulator not found, using dummy regulator [ 5.126270] L2 @ QSB rate. Forcing new rate. [ 5.131018] L2 @ 384000 KHz [ 5.135326] CPU0 @ 800000 KHz [ 5.137794] CPU1 @ QSB rate. Forcing new rate. [ 5.141034] CPU1 @ 384000 KHz [ 5.141706] mmc0: BKOPS_EN bit is not set [ 5.147584] mmc0: new high speed MMC card at address 0001 [ 5.152410] mmcblk0: mmc0:0001 MMC04G 3.57 GiB [ 5.153529] NET: Registered protocol family 26 [ 5.153551] GACT probability on [ 5.153569] Mirror/redirect action on [ 5.154689] netem: version 1.3 [ 5.154765] u32 classifier [ 5.154771] Performance counters on [ 5.154775] input device check on [ 5.154779] Actions configured [ 5.154815] Netfilter messages via NETLINK v0.30. [ 5.154842] nfnl_acct: registering with nfnetlink. [ 5.154944] nf_conntrack version 0.5.0 (7422 buckets, 29688 max) [ 5.155869] ctnetlink v0.93: registering with nfnetlink. [ 5.155902] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net> [ 5.156192] ipip: IPv4 over IPv4 tunneling driver [ 5.157385] gre: GRE over IPv4 demultiplexor driver [ 5.157392] ip_gre: GRE over IPv4 tunneling driver [ 5.159543] IPv4 over IPSec tunneling driver [ 5.160622] TCP: bic registered [ 5.160633] TCP: cubic registered [ 5.160642] TCP: westwood registered [ 5.160652] TCP: highspeed registered [ 5.160658] TCP: hybla registered [ 5.160665] TCP: htcp registered [ 5.160672] TCP: vegas registered [ 5.160679] TCP: veno registered [ 5.160685] TCP: scalable registered [ 5.160693] TCP: lp registered [ 5.160700] TCP: yeah registered [ 5.160707] TCP: illinois registered [ 5.160713] Initializing XFRM netlink socket [ 5.161823] NET: Registered protocol family 10 [ 5.164960] sit: IPv6 over IPv4 tunneling driver [ 5.167626] ip6_gre: GRE over IPv6 tunneling driver [ 5.168978] NET: Registered protocol family 17 [ 5.169049] NET: Registered protocol family 15 [ 5.169061] NET: Registered protocol family 5 [ 5.169245] l2tp_core: L2TP core driver, V2.0 [ 5.169284] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 5.169290] l2tp_netlink: L2TP netlink interface [ 5.170209] sctp: Hash tables configured (established 16384 bind 16384) [ 5.171071] openvswitch: Open vSwitch switching datapath [ 5.171511] mpls_gso: MPLS GSO support [ 5.197536] regulator-dummy: disabling [ 5.336704] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for vddcx [ 5.336852] mmcblk0boot0: mmc0:0001 MMC04G partition 1 2.00 MiB [ 5.337013] mmcblk0boot1: mmc0:0001 MMC04G partition 2 2.00 MiB [ 5.337167] mmcblk0rpmb: mmc0:0001 MMC04G partition 3 128 KiB [ 5.345034] mmcblk0: p1 p2 p3 p4 p5 [ 5.348415] mmcblk0boot1: unknown partition table [ 5.349828] mmcblk0boot0: unknown partition table [ 5.372625] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for v3p3 [ 5.377290] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for v1p8 [ 5.383721] regulator-dummy: operation not allowed [ 5.390221] regulator-dummy: operation not allowed [ 5.397228] qcom-dwc3-ssphy 110f8830.phy: cannot set voltage for vddcx [ 5.657433] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.657525] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 5.662721] xhci-hcd xhci-hcd.0.auto: irq 142, io mem 0x11000000 [ 5.669948] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.675631] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.682407] usb usb1: Product: xHCI Host Controller [ 5.689496] usb usb1: Manufacturer: Linux 3.14.0 xhci-hcd [ 5.694200] usb usb1: SerialNumber: xhci-hcd.0.auto [ 5.701169] hub 1-0:1.0: USB hub found [ 5.704514] hub 1-0:1.0: 1 port detected [ 5.709127] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.712366] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 5.718212] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 5.725195] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.732233] usb usb2: Product: xHCI Host Controller [ 5.739324] usb usb2: Manufacturer: Linux 3.14.0 xhci-hcd [ 5.744027] usb usb2: SerialNumber: xhci-hcd.0.auto [ 5.750880] hub 2-0:1.0: USB hub found [ 5.754328] hub 2-0:1.0: 1 port detected [ 5.759796] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for vddcx [ 5.762174] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for v3p3 [ 5.768660] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for v1p8 [ 5.775013] regulator-dummy: operation not allowed [ 5.781524] regulator-dummy: operation not allowed [ 5.788536] qcom-dwc3-ssphy 100f8830.phy: cannot set voltage for vddcx [ 6.047369] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 6.047449] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 6.052596] xhci-hcd xhci-hcd.1.auto: irq 237, io mem 0x10000000 [ 6.059810] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.065565] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.072383] usb usb3: Product: xHCI Host Controller [ 6.079434] usb usb3: Manufacturer: Linux 3.14.0 xhci-hcd [ 6.084136] usb usb3: SerialNumber: xhci-hcd.1.auto [ 6.090646] hub 3-0:1.0: USB hub found [ 6.094428] hub 3-0:1.0: 1 port detected [ 6.098746] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 6.102286] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 6.107988] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 6.115123] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.122136] usb usb4: Product: xHCI Host Controller [ 6.129256] usb usb4: Manufacturer: Linux 3.14.0 xhci-hcd [ 6.133957] usb usb4: SerialNumber: xhci-hcd.1.auto [ 6.140476] hub 4-0:1.0: USB hub found [ 6.144240] hub 4-0:1.0: 1 port detected [ 6.148845] SPEED BIN: 0 [ 6.152092] ACPU PVS: 2 [ 6.154639] deviceless supply vcore_regulator not found, using dummy regulator [ 6.156881] regulator-dummy: Failed to create debugfs directory [ 6.164364] Frequency table not initialized. [ 6.170062] Frequency table not initialized. [ 6.174445] Frequency table not initialized. [ 6.178734] Frequency table not initialized. [ 6.182910] Frequency table not initialized. [ 6.187415] Frequency table not initialized. [ 6.191472] Frequency table not initialized. [ 6.195689] Frequency table not initialized. [ 6.200057] Frequency table not initialized. [ 6.204175] Frequency table not initialized. [ 6.218326] Freeing unused kernel memory: 1652K (80b0d000 - 80caa000) argc == 8 argv[0]: "/bin/kinit" argv[1]: "root=/dev/mmcblk0p3" argv[2]: "loglevel=7" argv[3]: "rdinit=/bin/kinit" argv[4]: "rw" argv[5]: "single" argv[6]: "console=ttyMSM0,115200n8" argv[7]: "earlyprintk" Running ipconfig argc == 3 argv[0]: "IP-Config" argv[1]: "-i" argv[2]: "Linux kinit" IP-Config: no devices to configure kinit: do_mounts kinit: try_name mmcblk0,3 = mmcblk0p3(179,3) kinit: name_to_dev_t(/dev/mmcblk0p3) = mmcblk0p3(179,3) kinit: root_dev = mmcblk0p3(179,3) kinit: mounting root rw kinit: /dev/root appears to be a ext4 filesystem kinit: trying to mount /dev/root on /root with type ext4, flags 0x8000, data '(null)' [ 6.416902] usb 3-1: new full-speed USB device number 2 using xhci-hcd [ 6.557631] usb 3-1: New USB device found, idVendor=0cf3, idProduct=3004 [ 6.557659] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 8.142518] EXT4-fs (mmcblk0p3): recovery complete [ 8.144170] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) kinit: Mounted root (ext4 filesystem). Checking for init: /sbin/init Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory [ 8.718645] random: init urandom read with 93 bits of entropy available [ 9.200508] init: mounted-proc main process (282) terminated with status 1 Starting Hardware RNG entropy gatherer daemon: rngd. net.core.rmem_default = 8388608 net.core.wmem_default = 8388608 net.core.rmem_max = 8388608 net.core.wmem_max = 8388608 net.ipv4.tcp_wmem = 1048576 2097152 8388608 net.ipv4.tcp_rmem = 1048576 2097152 8388608 net.core.netdev_max_backlog = 2000 net.ipv4.ip_forward = 1 autoneg unmodified, ignoring autoneg unmodified, ignoring dev.nss.general.jumbo_mru = 9000 dev.nss.general.redirect = 1 sysctl: setting key "dev.nss.general.rps": Invalid argument dev.nss.general.rps = 1 e2fsck 1.42.9 (4-Feb-2014) /dev/mmcblk0p5 was not cleanly unmounted, check forced. Pass 1: Checking inodes, blocks, and sizes Pass 2: Checking directory structure Pass 3: Checking directory connectivity Pass 4: Checking reference counts Pass 5: Checking group summary information /dev/mmcblk0p5: 27/7936 files (0.0% non-contiguous), 1414/31744 blocks root@eero:~# [ 15.635527] AHB support is still work in progress [ 18.103697] watchdog watchdog0: watchdog did not stop! [ 27.653484] zorgo_0_0: Not creating an NSS virtual interface [ 28.903518] zorgo_1_0: Not creating an NSS virtual interface root@eero:~# root@eero:~#